EUTECH INSTRUMENTS PH 6 PLUS PH MV TEMP Manuel d'instructions Page 31
- Page / 64
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Instruction Manual CyberScan pH 1100/ 2100
31
10.2.3 pH resolution setup program P1.1
Use this program to select pH resolution (0.01 or 0.001 pH).
1. Enter pH/Temperature setup mode as described in steps 1-4
in 10.2.1 Entering pH/temperature setup mode (page 30).
2. Use ∆/MI key to scroll to program pH Resol. Setup: P1.1. See
Figure 83.
3. Press ENTER to enter program pH Resol. Setup: P1.1.
4. Press >/CAL to toggle between 0.01 and 0.001. The
resolution selected will flash. See Figure 84.
5. Press ENTER to confirm selection and return to the setup
mode. Press ∆/MI to continue to the next setup program, or
press ∇/MR to go to the previous program. Press EXIT to
return to the pH measurement mode.
10.2.4 Temperature unit setup program P1.2
Use this program to select temperature measurement unit (°C or
°F).
1. Enter pH/Temperature setup mode as described in steps 1-4
in 10.2.1 Entering pH/temperature setup mode (page 30).
2. Use ∆/MI key to scroll to program Temp Unit Setup: P1.2. See
Figure 85.
3. Press ENTER to enter program Temp Unit Setup: P1.2.
4. Press >/CAL to toggle between Degree C and Degree F. The
unit selected will flash. See Figure 86.
5. Press ENTER to confirm selection and return to the setup
mode. Press ∆/MI to continue to the next setup program, or
press ∇/MR to go to the previous program. Press EXIT to
return to the pH measurement mode.
Mode
Degree C Degree F
Select & Press ENTER
0.01 0.001
Select & Press ENTER
Temp Unit Setup:P1.2
Press ENT. to Select
pH Resol. Setup: P1.1
Press ENT. to Select
Figure 83
Figure 84
Figure 85
Figure 86
- Instruction Manual 1
- PREFACE 3
- TABLE OF CONTENTS 4
- 1 INTRODUCTION 6
- Figure 1: Membrane Keypad 7
- 1.3 Rear Panel 8
- 1.4 Electrode Holder 9
- 2 STARTING UP 10
- Attention: 10
- Selectable buffer sets: 11
- Figure 13 12
- Figure 14 12
- Figure 15 12
- . See Figure 17. This 13
- Cal Done 13
- NOTE: 14
- . See Figure 26. Press 15
- 3.2 pH measurement 16
- Figure 35 17
- Figure 36 17
- 18
- pH/Temp mV Ion 19
- 5.1 Ion calibration 20
- Ion Conc: 1.0ppm 21
- 3 Point Cal Done 21
- Aver. Slope = 49.2mV 21
- Sys Updating. . 21
- 5.3 Ion measurement 22
- 5.695pH 25.3 C ATC 23
- Data Log. . . . Loc: 9 23
- 6.2 Memory recall 24
- 7.546pH 25.4 C ATC 25
- 9.1 Temperature Calibration 26
- 10.1 Setup mode overview 27
- Tx/Rx Parameter: P4.4 29
- Press ENT. to Select 29
- USA NST Bf1 Bf2 Cust 30
- Select & Press ENTER 30
- Figure 83 31
- Figure 84 31
- Figure 85 31
- Figure 86 31
- Key In Low Alarm 32
- Key In High Alarm 32
- Figure 91 33
- Figure 92 33
- Figure 93 33
- Figure 94 34
- Figure 95 34
- Figure 96 34
- Figure 101 35
- = 0.2 mV 35
- Figure 105 36
- Figure 106 36
- Figure 107 36
- Figure 108 36
- Figure 109 37
- Figure 110 37
- Figure 111 37
- Figure 112 38
- Figure 113 38
- Figure 1 38
- Figure 115 38
- Figure 116 39
- Figure 117 39
- Figure 118 39
- Figure 119 40
- Figure 120 40
- Figure 121 40
- Figure 124 41
- = 3.2 mV 41
- Figure 125 42
- Figure 126 42
- Figure 127 42
- Figure 128 42
- Figure 132 43
- Figure 133 43
- Figure 134 44
- Figure 135 44
- Figure 136 44
- Figure 137 44
- Figure 138 45
- Figure 139 45
- Figure 140 45
- Figure 141 46
- Figure 142 46
- Figure 143 46
- Resolution: High Low 47
- Ion Mode Setup : P3.4 47
- Figure 155 49
- Figure 156 49
- Figure 157 49
- Figure 158 49
- Figure 167 51
- Figure 168 51
- Figure 169 51
- Memory Recall Mode 52
- Auto Manual 52
- MemRecall Setup:P4.3 52
- Data send to printer 53
- Current Memory 53
- Data Transfer :P4.5 53
- Figure 185 54
- Figure 186 54
- Figure 187 54
- Figure 184 54
- 11 ELECTRODE CARE 55
- 12 RS 232 COMMUNICATION 56
- 13 ADDITIONAL INFORMATION 57
- Offset of temp. probe 59
- Temperature 60
- 17 ACCESSORIES 61
- 18 WARRANTY 62
Produits connexes et manuels pour Mesure, test et contrôle EUTECH INSTRUMENTS PH 6 PLUS PH MV TEMP
(4 pages)
Mesure, test et contrôle EUTECH INSTRUMENTS ECOSCAN TEMP JKT PORTABLE METER Manuel d'instructions
(20 pages)
(20 pages)
Mesure, test et contrôle EUTECH INSTRUMENTS ECOSCAN TEMP 456 TEMPERATURE METER Manuel d'instructions
(24 pages)
(24 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.092 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels