EUTECH INSTRUMENTS PH 6 PLUS PH MV TEMP Manuel d'instructions Page 13
- Page / 64
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Instruction Manual CyberScan pH 1100/ 2100
13
3.1.3 Standard pH buffer calibration
1. When entering the standard calibration mode, the first buffer
calibration point for standard pH buffers is 7.000 or 6.860
(depending upon which pH buffer set is selected). The upper
display shows the current reading, the lower display will show
Auto Buf Scan: 7.000 (or 6.860). The upper display will flash pH
until the reading has stabilized. See Figure 16. If the selected
buffer value is not within ±1.0 of the measured pH value, the
Auto pH Scan will continue to change until the pH buffer is
within ±1.0.
2. When pH reading has stabilized, press ENTER. The lower
display flashes *pH Offset Cal Done. See Figure 17. This
calibration point is now stored in the meter.
• If you are performing a one-point calibration, press EXIT.
The screen flashes Sys Updating...Please wait....The meter
then returns to the pH measurement mode. You may now
start taking pH readings.
• If you are performing a multi-point calibration, go to step 3.
3. Rinse the probe with deionized water or a rinse solution, and
place it in the next pH buffer. The lower display automatically
scans to the next pH buffer solution.
4. Wait for the measured pH value to stabilize. The upper display
will flash pH until the reading has stabilized.
5. When pH reading has stabilized, press ENTER. The lower
display flashes 2 Point Cal Done * (3 if you have calibrated 3
points,4 if 4 points, etc.). See Figure 18. This calibration point is
now stored in the meter. Repeat steps 3-5 for each point you
wish to calibrate. When you are finished calibrating, press EXIT.
The screen flashes Sys. Updating... Please wait.... The meter
then returns to the pH measurement mode. You may now start
taking pH readings.
6. If you perform a complete 5-point pH calibration, when you
calibrate the fifth point and press ENTER, the meter
automatically returns to measurement mode. You may now start
taking pH readings.
NOTE:
To exit from pH calibration mode at any point without confirming calibration, DO NOT press ENTER in steps 2, 5 or 6.
Press EXIT instead. If EXIT is press before a 1-point calibration is performed the upper display flashes Error: Cal Aborted.
See Figure 19.
DO NOT REUSE SOLUTIONS AFTER CALIBRATION.
Contaminants in the solution can affect the calibration, and eventually the accuracy of the measurements.
Figure 16
Figure 17
Figure 18
Figure 19
7.001pH 25.4 C ATC
Auto Buf Scan: 7.000
°
7.001pH 25.4 C ATC
pH Offset Cal Done
°
*
Error: Cal Aborted
10.010
2 Point Cal Done
*
pH 25.4 C ATC
°
- Instruction Manual 1
- PREFACE 3
- TABLE OF CONTENTS 4
- 1 INTRODUCTION 6
- Figure 1: Membrane Keypad 7
- 1.3 Rear Panel 8
- 1.4 Electrode Holder 9
- 2 STARTING UP 10
- Attention: 10
- Selectable buffer sets: 11
- Figure 13 12
- Figure 14 12
- Figure 15 12
- . See Figure 17. This 13
- Cal Done 13
- NOTE: 14
- . See Figure 26. Press 15
- 3.2 pH measurement 16
- Figure 35 17
- Figure 36 17
- 18
- pH/Temp mV Ion 19
- 5.1 Ion calibration 20
- Ion Conc: 1.0ppm 21
- 3 Point Cal Done 21
- Aver. Slope = 49.2mV 21
- Sys Updating. . 21
- 5.3 Ion measurement 22
- 5.695pH 25.3 C ATC 23
- Data Log. . . . Loc: 9 23
- 6.2 Memory recall 24
- 7.546pH 25.4 C ATC 25
- 9.1 Temperature Calibration 26
- 10.1 Setup mode overview 27
- Tx/Rx Parameter: P4.4 29
- Press ENT. to Select 29
- USA NST Bf1 Bf2 Cust 30
- Select & Press ENTER 30
- Figure 83 31
- Figure 84 31
- Figure 85 31
- Figure 86 31
- Key In Low Alarm 32
- Key In High Alarm 32
- Figure 91 33
- Figure 92 33
- Figure 93 33
- Figure 94 34
- Figure 95 34
- Figure 96 34
- Figure 101 35
- = 0.2 mV 35
- Figure 105 36
- Figure 106 36
- Figure 107 36
- Figure 108 36
- Figure 109 37
- Figure 110 37
- Figure 111 37
- Figure 112 38
- Figure 113 38
- Figure 1 38
- Figure 115 38
- Figure 116 39
- Figure 117 39
- Figure 118 39
- Figure 119 40
- Figure 120 40
- Figure 121 40
- Figure 124 41
- = 3.2 mV 41
- Figure 125 42
- Figure 126 42
- Figure 127 42
- Figure 128 42
- Figure 132 43
- Figure 133 43
- Figure 134 44
- Figure 135 44
- Figure 136 44
- Figure 137 44
- Figure 138 45
- Figure 139 45
- Figure 140 45
- Figure 141 46
- Figure 142 46
- Figure 143 46
- Resolution: High Low 47
- Ion Mode Setup : P3.4 47
- Figure 155 49
- Figure 156 49
- Figure 157 49
- Figure 158 49
- Figure 167 51
- Figure 168 51
- Figure 169 51
- Memory Recall Mode 52
- Auto Manual 52
- MemRecall Setup:P4.3 52
- Data send to printer 53
- Current Memory 53
- Data Transfer :P4.5 53
- Figure 185 54
- Figure 186 54
- Figure 187 54
- Figure 184 54
- 11 ELECTRODE CARE 55
- 12 RS 232 COMMUNICATION 56
- 13 ADDITIONAL INFORMATION 57
- Offset of temp. probe 59
- Temperature 60
- 17 ACCESSORIES 61
- 18 WARRANTY 62
Produits connexes et manuels pour Mesure, test et contrôle EUTECH INSTRUMENTS PH 6 PLUS PH MV TEMP
(4 pages)
Mesure, test et contrôle EUTECH INSTRUMENTS ECOSCAN TEMP JKT PORTABLE METER Manuel d'instructions
(20 pages)
(20 pages)
Mesure, test et contrôle EUTECH INSTRUMENTS ECOSCAN TEMP 456 TEMPERATURE METER Manuel d'instructions
(24 pages)
(24 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.128 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels