EUTECH INSTRUMENTS PH 6 PLUS PH MV TEMP Manuel d'instructions Page 27
- Page / 64
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Instruction Manual CyberScan pH 1100/ 2100
27
10 SETUP MODE
The advanced setup mode lets you customize your meter’s preferences and defaults. The pH 2100 benchtop meter
features 4 different setup modes (the pH 1100 meter features 3 modes):
1. pH/Temperature
2. mV
3. Ion (pH 2100 only)
4. Meter general configuration
Each setup mode has submenus to configure specific meter parameters.
10.1 Setup mode overview
10.1.1 pH/Temperature setup submenus
Press SETUP to enter setup mode from the pH measurement mode. Use >/CAL to select pH/Temp, and then press
ENTER to enter pH/Temp setup mode. Use the ∆/MI and ∇/MR keys to scroll through sub menus. There are 8 sub
menus (programs) in the pH/Temperature setup mode:
pHCalDue Alarm: P1.4
Press ENT. to Select
Stability Setup: P1.5
Press ENT. to Select
pH Cal Data :P1.6
Press ENT. to Select
pH Cal Reset :P1.7
Press ENT. to Select
pH Buffer Setup:P1. 0
pH Resolution Setup:P1.1
Temperature Unit Setup:P1.2
pH Measurement Alarm
Setup P1.3
-Selects calibration buffer sets
(USA, NIST, Bf1, Bf2 or
custom)
-Selects pH resolution
(0.01 or 0. 001 pH)
-Selects temperature
measurement unit (°C or °F)
-Sets low and high pH alarm
pH Calibration Due Alarm
Setup:P1.4
Stability Setup:P1.5
View Calibration Data:P1.6
pH Calibration Reset:P1.7
-Sets calibration reminder
alarm, select 1 -365 days
from last calibration date
-Sets stability indicator
criteria, off or on (high,
medium or low )
-Last pH calibration
date/time
-pH buffer set selected
-pH calibration temperature
and temperature
compensation mode
-pH offset value
-pH slopes (from acid to
alkaline)
-Clears all pH calibration
data
see page 30
see page 31
see page 31
see page 32
see page 33
see page 34
see page 35
see page 36
pH Buffer Setup: P1.0
Press ENT. to Select
pH Resol. Setup: P1.1
Press ENT. to Select
Temp Unit Setup:P1.2
Press ENT. to Select
pH Meas. Alarm :P1.3
Press ENT. to Select
- Instruction Manual 1
- PREFACE 3
- TABLE OF CONTENTS 4
- 1 INTRODUCTION 6
- Figure 1: Membrane Keypad 7
- 1.3 Rear Panel 8
- 1.4 Electrode Holder 9
- 2 STARTING UP 10
- Attention: 10
- Selectable buffer sets: 11
- Figure 13 12
- Figure 14 12
- Figure 15 12
- . See Figure 17. This 13
- Cal Done 13
- NOTE: 14
- . See Figure 26. Press 15
- 3.2 pH measurement 16
- Figure 35 17
- Figure 36 17
- 18
- pH/Temp mV Ion 19
- 5.1 Ion calibration 20
- Ion Conc: 1.0ppm 21
- 3 Point Cal Done 21
- Aver. Slope = 49.2mV 21
- Sys Updating. . 21
- 5.3 Ion measurement 22
- 5.695pH 25.3 C ATC 23
- Data Log. . . . Loc: 9 23
- 6.2 Memory recall 24
- 7.546pH 25.4 C ATC 25
- 9.1 Temperature Calibration 26
- 10.1 Setup mode overview 27
- Tx/Rx Parameter: P4.4 29
- Press ENT. to Select 29
- USA NST Bf1 Bf2 Cust 30
- Select & Press ENTER 30
- Figure 83 31
- Figure 84 31
- Figure 85 31
- Figure 86 31
- Key In Low Alarm 32
- Key In High Alarm 32
- Figure 91 33
- Figure 92 33
- Figure 93 33
- Figure 94 34
- Figure 95 34
- Figure 96 34
- Figure 101 35
- = 0.2 mV 35
- Figure 105 36
- Figure 106 36
- Figure 107 36
- Figure 108 36
- Figure 109 37
- Figure 110 37
- Figure 111 37
- Figure 112 38
- Figure 113 38
- Figure 1 38
- Figure 115 38
- Figure 116 39
- Figure 117 39
- Figure 118 39
- Figure 119 40
- Figure 120 40
- Figure 121 40
- Figure 124 41
- = 3.2 mV 41
- Figure 125 42
- Figure 126 42
- Figure 127 42
- Figure 128 42
- Figure 132 43
- Figure 133 43
- Figure 134 44
- Figure 135 44
- Figure 136 44
- Figure 137 44
- Figure 138 45
- Figure 139 45
- Figure 140 45
- Figure 141 46
- Figure 142 46
- Figure 143 46
- Resolution: High Low 47
- Ion Mode Setup : P3.4 47
- Figure 155 49
- Figure 156 49
- Figure 157 49
- Figure 158 49
- Figure 167 51
- Figure 168 51
- Figure 169 51
- Memory Recall Mode 52
- Auto Manual 52
- MemRecall Setup:P4.3 52
- Data send to printer 53
- Current Memory 53
- Data Transfer :P4.5 53
- Figure 185 54
- Figure 186 54
- Figure 187 54
- Figure 184 54
- 11 ELECTRODE CARE 55
- 12 RS 232 COMMUNICATION 56
- 13 ADDITIONAL INFORMATION 57
- Offset of temp. probe 59
- Temperature 60
- 17 ACCESSORIES 61
- 18 WARRANTY 62
Produits connexes et manuels pour Mesure, test et contrôle EUTECH INSTRUMENTS PH 6 PLUS PH MV TEMP
(4 pages)
Mesure, test et contrôle EUTECH INSTRUMENTS ECOSCAN TEMP JKT PORTABLE METER Manuel d'instructions
(20 pages)
(20 pages)
Mesure, test et contrôle EUTECH INSTRUMENTS ECOSCAN TEMP 456 TEMPERATURE METER Manuel d'instructions
(24 pages)
(24 pages)
© 2020, manymanuals.fr. Tous droits réservés | 1.634 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels