EUTECH INSTRUMENTS PH 6 PLUS PH MV TEMP Manuel d'instructions Page 25
- Page / 64
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Instruction Manual CyberScan pH 1100/ 2100
25
7 STABILITY INDICATOR
The stability indicator signals when pH, mV or Ion readings are stable.
The pH, mV or Ion annunciator will blink when reading are not stable.
See Figure 68. Once the reading becomes stable the annunciator
becomes static and no longer blinks.
You can turn the stability indicator on and off and set the level of
stability in pH Setup Section P1.5 (page 34); mV Setup P2.2 (page
40); and Ion Setup P3.3 (page 46).
8 ALARM FUNCTIONS
8.1 High and Low measurement alarm
Your meter has high and low measurement alarms that can be individually set for pH, mV and Ion (pH 2100 only). To set
high and low measurement alarms, please refer to the setup sections pH Setup P1.3 (page 32); mV Setup P2.0 (page
38); and Ion Setup P3.1 (page 44).
If the measured value exceeds the alarm setting, the meter will “beep”; the upper display flashes measured parameter
flashes; and the lower displays Hi-Alarm or Lo-Alarm. See Figures 69 and 70.
The following conditions are necessary to signal an alarm:
• pH: The high alarm must be at least 1.0 pH greater than
the low alarm
• mV: The high alarm setting must be at least 100.0
greater than the low alarm
• Ion: The high alarm setting must be at least half of the
next decade greater than the low alarm
8.2 Calibration due alarm
You can set this meter to signal an alarm when calibration is due.
Individual calibration due alarms can be set for pH, mV and Ion
(pH 2100 only) at a period of 1 to 365 days from the last calibration.
To set calibration due alarm, please refer to the setup sections pH
Setup P1.4 (page 33); mV Setup P2.1 (page 39); and Ion Setup
P3.2 (page 45). The meter will “beep” during power up if
calibration is due. The upper display will read pH (mV or Ion)
Calibration Due, the lower display will flash Calibration and read
Abort. See Figure 71.
Use >/CAL to select Calibration or Abort.
• Select Calibration to enter calibration mode and begin
meter calibration.
• Select Abort to override alarm. Meter reverts to
measurement mode.
Press ENTER to confirm selection.
7.546pH 25.4 C ATC
Jan 18 2002 08:46:30
°
Figure 68
2.852pH 25.3 C ATC
Lo-Alarm 08:46:25
°
pH Calibration Due
Calibration Abort
13.278pH 28.6 C ATC
Hi-Alarm 08:46:25
°
Figure 69
Figure 70
Figure 71
- Instruction Manual 1
- PREFACE 3
- TABLE OF CONTENTS 4
- 1 INTRODUCTION 6
- Figure 1: Membrane Keypad 7
- 1.3 Rear Panel 8
- 1.4 Electrode Holder 9
- 2 STARTING UP 10
- Attention: 10
- Selectable buffer sets: 11
- Figure 13 12
- Figure 14 12
- Figure 15 12
- . See Figure 17. This 13
- Cal Done 13
- NOTE: 14
- . See Figure 26. Press 15
- 3.2 pH measurement 16
- Figure 35 17
- Figure 36 17
- 18
- pH/Temp mV Ion 19
- 5.1 Ion calibration 20
- Ion Conc: 1.0ppm 21
- 3 Point Cal Done 21
- Aver. Slope = 49.2mV 21
- Sys Updating. . 21
- 5.3 Ion measurement 22
- 5.695pH 25.3 C ATC 23
- Data Log. . . . Loc: 9 23
- 6.2 Memory recall 24
- 7.546pH 25.4 C ATC 25
- 9.1 Temperature Calibration 26
- 10.1 Setup mode overview 27
- Tx/Rx Parameter: P4.4 29
- Press ENT. to Select 29
- USA NST Bf1 Bf2 Cust 30
- Select & Press ENTER 30
- Figure 83 31
- Figure 84 31
- Figure 85 31
- Figure 86 31
- Key In Low Alarm 32
- Key In High Alarm 32
- Figure 91 33
- Figure 92 33
- Figure 93 33
- Figure 94 34
- Figure 95 34
- Figure 96 34
- Figure 101 35
- = 0.2 mV 35
- Figure 105 36
- Figure 106 36
- Figure 107 36
- Figure 108 36
- Figure 109 37
- Figure 110 37
- Figure 111 37
- Figure 112 38
- Figure 113 38
- Figure 1 38
- Figure 115 38
- Figure 116 39
- Figure 117 39
- Figure 118 39
- Figure 119 40
- Figure 120 40
- Figure 121 40
- Figure 124 41
- = 3.2 mV 41
- Figure 125 42
- Figure 126 42
- Figure 127 42
- Figure 128 42
- Figure 132 43
- Figure 133 43
- Figure 134 44
- Figure 135 44
- Figure 136 44
- Figure 137 44
- Figure 138 45
- Figure 139 45
- Figure 140 45
- Figure 141 46
- Figure 142 46
- Figure 143 46
- Resolution: High Low 47
- Ion Mode Setup : P3.4 47
- Figure 155 49
- Figure 156 49
- Figure 157 49
- Figure 158 49
- Figure 167 51
- Figure 168 51
- Figure 169 51
- Memory Recall Mode 52
- Auto Manual 52
- MemRecall Setup:P4.3 52
- Data send to printer 53
- Current Memory 53
- Data Transfer :P4.5 53
- Figure 185 54
- Figure 186 54
- Figure 187 54
- Figure 184 54
- 11 ELECTRODE CARE 55
- 12 RS 232 COMMUNICATION 56
- 13 ADDITIONAL INFORMATION 57
- Offset of temp. probe 59
- Temperature 60
- 17 ACCESSORIES 61
- 18 WARRANTY 62
Produits connexes et manuels pour Mesure, test et contrôle EUTECH INSTRUMENTS PH 6 PLUS PH MV TEMP
(4 pages)
Mesure, test et contrôle EUTECH INSTRUMENTS ECOSCAN TEMP JKT PORTABLE METER Manuel d'instructions
(20 pages)
(20 pages)
Mesure, test et contrôle EUTECH INSTRUMENTS ECOSCAN TEMP 456 TEMPERATURE METER Manuel d'instructions
(24 pages)
(24 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.215 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels