EUTECH INSTRUMENTS PH 6 PLUS PH MV TEMP Manuel d'instructions Page 54
- Page / 64
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Instruction Manual CyberScan pH 1100/ 2100
54
10.5.8 Memory clear setup mode P4.6
Clears all pH, mV and Ion (pH2100 only) memory points stored
in memory.
1. Enter meter setup mode as described in steps 1-4 in Section
10.5.1 Entering meter setup mode (page 50).
2. Use ∆/MI key to scroll to program Mem Clear Setup: P4.6.
See Figure 181.
3. Press ENTER to enter program Mem Clear Setup: P4.6.
4. Press >/CAL key to toggle between Memory Clear Yes and No.
The selection will flash. See Figure 182.
5. Press ENTER to confirm selection.
• If you select Yes, the screen flashes Memory being
Cleared, Please wait... See Figure 183. The meter then
returns to the setup mode.
• If you select No, the meter returns to the setup mode.
Press ∆/MI to continue to the next setup program, or
press ∇/MR to go to the previous program. Press EXIT to
return to measurement mode.
10.5.9 Meter reset setup mode P4.7
Resets the meter to factory default settings:
• pH/mV/Ion* calibration data is erased
• Manual temperature compensation is set to 25.0°C
• pH/mV/Ion* measurement alarm is off
• pH/mV/Ion* calibration due alarm is off
• Stability indicator is turned on with low stability setting
• Data logging and memory recall has manual setting
• Backlight is on with 2.0 minute duration
• Memory is cleared
*Ion features on the CyberScan pH2100 meter only
1. Enter meter setup mode as described in steps 1-4 in Section
10.5.1 Entering meter setup mode (page 50).
2. Use ∆/MI key to scroll to program Meter Reset: P4.7.
See Figure 184.
3. Press ENTER to enter program Meter Reset: P4.7.
4. Press >/CAL key to toggle between Meter Reset Yes and No.
The selection will flash. See Figure 185.
5. Press ENTER to confirm selection.
• If you selected Yes, the screen flashes Meter being
Reset, Please wait...See Figure 186. The meter then
returns to measurement mode.
• If you select No, the screen flashes Reset Aborted. See
Figure 187. The meter then returns to the measurement
mode.
Memory being Cleared
Please wait. . .
Memory Clear:Yes No
Select & Press ENTER
Mem Clear Setup :P4.6
Press ENT. to Select
Figure 181
Figure 182
Figure 183
Meter being Reset
Please wait. . .
Meter Reset: Yes No
Select & Press ENTER
Meter Reset :P4.7
Press ENT. to Select
Figure 184
Figure 185
Figure 186
Figure 187
Reset Aborted
- Instruction Manual 1
- PREFACE 3
- TABLE OF CONTENTS 4
- 1 INTRODUCTION 6
- Figure 1: Membrane Keypad 7
- 1.3 Rear Panel 8
- 1.4 Electrode Holder 9
- 2 STARTING UP 10
- Attention: 10
- Selectable buffer sets: 11
- Figure 13 12
- Figure 14 12
- Figure 15 12
- . See Figure 17. This 13
- Cal Done 13
- NOTE: 14
- . See Figure 26. Press 15
- 3.2 pH measurement 16
- Figure 35 17
- Figure 36 17
- 18
- pH/Temp mV Ion 19
- 5.1 Ion calibration 20
- Ion Conc: 1.0ppm 21
- 3 Point Cal Done 21
- Aver. Slope = 49.2mV 21
- Sys Updating. . 21
- 5.3 Ion measurement 22
- 5.695pH 25.3 C ATC 23
- Data Log. . . . Loc: 9 23
- 6.2 Memory recall 24
- 7.546pH 25.4 C ATC 25
- 9.1 Temperature Calibration 26
- 10.1 Setup mode overview 27
- Tx/Rx Parameter: P4.4 29
- Press ENT. to Select 29
- USA NST Bf1 Bf2 Cust 30
- Select & Press ENTER 30
- Figure 83 31
- Figure 84 31
- Figure 85 31
- Figure 86 31
- Key In Low Alarm 32
- Key In High Alarm 32
- Figure 91 33
- Figure 92 33
- Figure 93 33
- Figure 94 34
- Figure 95 34
- Figure 96 34
- Figure 101 35
- = 0.2 mV 35
- Figure 105 36
- Figure 106 36
- Figure 107 36
- Figure 108 36
- Figure 109 37
- Figure 110 37
- Figure 111 37
- Figure 112 38
- Figure 113 38
- Figure 1 38
- Figure 115 38
- Figure 116 39
- Figure 117 39
- Figure 118 39
- Figure 119 40
- Figure 120 40
- Figure 121 40
- Figure 124 41
- = 3.2 mV 41
- Figure 125 42
- Figure 126 42
- Figure 127 42
- Figure 128 42
- Figure 132 43
- Figure 133 43
- Figure 134 44
- Figure 135 44
- Figure 136 44
- Figure 137 44
- Figure 138 45
- Figure 139 45
- Figure 140 45
- Figure 141 46
- Figure 142 46
- Figure 143 46
- Resolution: High Low 47
- Ion Mode Setup : P3.4 47
- Figure 155 49
- Figure 156 49
- Figure 157 49
- Figure 158 49
- Figure 167 51
- Figure 168 51
- Figure 169 51
- Memory Recall Mode 52
- Auto Manual 52
- MemRecall Setup:P4.3 52
- Data send to printer 53
- Current Memory 53
- Data Transfer :P4.5 53
- Figure 185 54
- Figure 186 54
- Figure 187 54
- Figure 184 54
- 11 ELECTRODE CARE 55
- 12 RS 232 COMMUNICATION 56
- 13 ADDITIONAL INFORMATION 57
- Offset of temp. probe 59
- Temperature 60
- 17 ACCESSORIES 61
- 18 WARRANTY 62
Produits connexes et manuels pour Mesure, test et contrôle EUTECH INSTRUMENTS PH 6 PLUS PH MV TEMP
(4 pages)
Mesure, test et contrôle EUTECH INSTRUMENTS ECOSCAN TEMP JKT PORTABLE METER Manuel d'instructions
(20 pages)
(20 pages)
Mesure, test et contrôle EUTECH INSTRUMENTS ECOSCAN TEMP 456 TEMPERATURE METER Manuel d'instructions
(24 pages)
(24 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.277 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels